Product Overview
The F-635199.TR1 is a single-row tapered roller bearing with boundary dimensions 40 mm bore × 70 mm outside diameter × 13/17 mm stepped width. The “TR1” suffix in Schaeffler/FAG nomenclature explicitly denotes single-row tapered roller bearing construction. It is catalogued as an automotive transmission bearing (cuscinetti per trasmissioni automobilistiche) and is designed to carry the combined radial and axial loads generated by the gear train in a gearbox assembly. The bearing is supplied open (without integral seals) for lubrication by the transmission oil circuit.
Critical field corrections before publication (Check column reasons)
① Cage material: the form specifies Nylon, but FAG TR1 tapered roller bearings use stamped steel cages.
The supplier form specifies Cage Type: Nylon cage / Nylon. However, the TR1 series in FAG nomenclature is consistently documented with stamped sheet steel cages: “Single row tapered roller bearings have a stamped cage made of sheet steel” and “(Z-5..TR1 or F-8..TR1)” confirms the TR1 designation uses a steel cage configuration. A nylon cage in a TR1 tapered roller bearing would be an unusual production variant and is not supported by the available catalogue data. The Cage fields should be corrected to “Stamped steel cage / Steel” unless the supplier can provide physical stock evidence that this specific batch is nylon-caged.
② HS Code is correct (8482500090), but the Cage and Feature fields must be aligned with the tapered roller structure.
The supplier form’s HS Code 8482500090 is correct for tapered roller bearings and should be retained. The Structure field (“Taper roller bearings”) and Number of Rows (“Single”) are also correct. The Feature field (“Non-standard taper roller bearings”) is acceptable. The primary inconsistency is the Nylon cage specification, which conflicts with the verified TR1-series steel cage configuration.
③ Weight, Cr, C0r, and speed ratings are not published for this specific designation.
The supplier form leaves Weight, Cr, C0r, grease speed, and oil speed blank. No accessible public catalogue publishes these values for the F-635199.TR1 in its 40 × 70 × 13/17 mm envelope. These fields should remain blank or be marked “Consult supplier” rather than estimated from a generic 40 mm bore tapered roller bearing. This is consistent with the pattern across the preceding vehicle-specific transmission bearing listings: OEM gearbox bearings are specified by fitment and assembly position, and public load ratings are often not released.
④ The stepped width 13/17 mm should be retained as a two-value dimension.
The 13/17 mm designation is a stepped or asymmetric width, understood as the inner-ring width and outer-ring or overall width respectively. The listing should retain the two-value format; reducing it to a single figure would misrepresent the envelope.
Key Specifications (corrected)
| Parameter | Value |
|---|---|
| Model | F-635199.TR1 |
| Type | Single-row tapered roller bearing(TR1 suffix = single-row tapered roller) |
| Bore diameter(d) | 40 mm |
| Outside diameter(D) | 70 mm |
| Width(B/T) | 13 / 17 mm(stepped / asymmetric width) |
| Weight | Consult supplier(not published in accessible catalogues) |
| Rolling element material | GCr15 chrome steel |
| Cage | Stamped steel cage(per FAG TR1-series standard)— correct the supplier form’s “Nylon” entry |
| Seals | Open / no seals |
| Load direction | Radial and axial(combined) |
| HS Code | 8482500090(tapered roller bearings) |
| Application | Automotive transmission bearing |
Performance Features
-
Single-row tapered roller geometry:The conical raceways support combined radial and axial loads simultaneously, with axial capacity in one direction. The tapered design provides the stiffness required for gear-mesh loads in transmission service.
-
Stepped 13/17 mm width:The asymmetric width provides defined axial location within the transmission housing, simplifying bearing setting and shaft end-play adjustment during assembly.
-
Stamped steel cage(TR1-series standard):The pressed steel cage retains and guides the tapered rollers under the cyclic loading of gearbox operation, and is the verified cage configuration for the TR1 series.
-
Open configuration for oil-circuit lubrication:No integral seals; the bearing relies on the transmission oil for lubrication and cooling, consistent with the wet-sump strategy of a gearbox.
-
GCr15 chrome steel construction:Rings and rollers are through-hardened for rolling-contact fatigue resistance under the cyclic loading of automotive transmission service.
Application
The F-635199.TR1 is catalogued as an automotive transmission bearing(cuscinetti per trasmissioni automobilistiche). In service, it supports a gear shaft under the combined radial and axial loads generated by the transmission gear train. The 40 × 70 × 13/17 mm envelope and the open, oil-lubricated configuration are consistent with a direct-fit transmission service bearing. Replacement requires transmission disassembly and should follow the vehicle manufacturer’s procedure for shaft end-play and bearing preload adjustment.
Ordering & Logistics
| Item | Detail |
|---|---|
| Stock | 77 pcs |
| Minimum order | 1 pc |
| FOB price | US$10 – US$50 per piece |
| Payment | PayPal / Western Union / T/T (100% in advance) |
| Delivery | 3–4 workdays after payment |
| Shipping | DHL / FedEx / UPS / TNT |
| Ports | Shanghai / Guangzhou |
| Packing | Standard export packing |
| OEM service | Available |
| Brand | As required (authorized brands only) |
| Country of origin | China |
| Company | WUXI MUFA TECHNOLOGY CO.,LTD. |
| Sales | Alice Wong |
| [email protected] | |
| +86 13771165326 | |
| mufatec-bearings |















