Product Overview
The F-624126 is a single-row cylindrical roller bearing without an inner ring, manufactured by INA with boundary dimensions 40 mm × 61.5 mm × 17.5 mm. It is catalogued as an automotive gearbox bearing and is designed to run directly on a hardened shaft or gear journal that serves as the inner raceway. The bearing uses a nylon cage and is supplied open (without integral seals) for lubrication by the transmission oil circuit.
Check Column NO — Root Causes and Corrections
① Cage Material: The form specifies "Steel cage / Steel", but the catalogue data consistently specifies a nylon cage.
The supplier form specifies Cage Type: Steel cage and Cage material: Steel. However, the INA F-624126 specification sheets from multiple sources consistently list "Cage type: nylon" and "Nylon Kafes" (nylon cage). This is a direct contradiction between the form and the catalogue data and is the most likely cause of the Check column failure.
Correction: Change Cage Type to "Nylon cage" and Cage material to "Nylon (Polyamide)".
② Seal Material, Weight, and Other Fields Are Blank
The supplier form correctly sets Seals Type: Open, but leaves Seal Material blank. The catalogue data confirms "Seal Type: Open", so Seal Material should be populated with "No seals". The Weight field is also blank; the available catalogue data states "Contact us to know" or "Liên hệ với chúng tôi để biết", meaning no published weight exists. For platform validation, populate Weight with "Consult supplier" or obtain an exact figure from the supplier's inspection sheet.
③ Bearing Material and Roller Material Are Blank or Misapplied
Bearing Material is blank. The catalogue data specifies "Chrome steel" and "GCr15", so populate Bearing Material = GCr15 chrome steel. Number of Balls, Ball Material, and Number of Roller are blank; for a cylindrical roller bearing, set Ball Material = Not applicable and Number of Balls = Not applicable. Roller Material is already set to GCr15 chrome steel, which is correct, but Number of Roller should be populated with "Consult supplier".
④ HS Code: 8482500090 is correct for cylindrical roller bearings; 8482800000 also appears in catalogue data
The supplier form uses HS Code 8482500090, which is the specific classification for cylindrical roller bearings. One catalogue page lists 8482800000 (other rolling bearings), but 8482500090 is the more precise and appropriate code for this product and should be retained. The discrepancy is unlikely to be the primary cause of the Check failure.
⑤ Inside Diameter Is Correct as Fw (Roller Complement Bore), Not a Conventional Inner Ring Bore
The form lists Inside Diameter: 40. Because the bearing is without an inner ring, the 40 mm dimension is the roller complement bore (Fw) — the diameter of the circle inscribed by the rollers — not a conventional inner-ring bore. This value is correct and matches the catalogue data. The listing description should clarify this to avoid buyer confusion.
Key Specifications (Corrected)
| Parameter | Value |
|---|---|
| Model | F-624126 |
| Brand reference | INA F-624126 |
| Type | Single-row cylindrical roller bearing, without inner ring (open) |
| Bore (Fw, roller complement bore) | 40 mm (runs directly on a hardened shaft journal) |
| Outside diameter (D) | 61.5 mm |
| Width (B) | 17.5 mm |
| Weight | Consult supplier (not published in accessible catalogues) |
| Bearing material | GCr15 chrome steel |
| Cage | Nylon cage (catalogue-confirmed) |
| Seals | Open / no seals |
| Load direction | Radial (cylindrical roller geometry is designed primarily for radial load) |
| HS Code | 8482500090 (cylindrical roller bearings) |
| Application | Automotive gearbox bearing |
Dimensional variant note: One Vietnamese supplier page lists the F-624126 as 39.5 × 61.5 × 17 mm rather than 40 × 61.5 × 17.5 mm. The 40 × 61.5 × 17.5 mm envelope is the one consistently reported by the INA catalogue pages and should be retained as the primary specification, but the supplier should confirm the physical stock measurement if the platform performs strict dimensional validation.
Performance Features
-
Without inner ring — shaft as raceway: The inner-ring-free design allows the cylindrical roller complement to run directly on a hardened and ground shaft journal, reducing the radial cross-section of the bearing assembly. This is a key advantage in space-constrained gearbox housings where every millimetre of radial clearance matters.
-
High radial load capacity in a compact envelope: Cylindrical roller bearings have line contact between rollers and raceways, giving them significantly higher radial load capacity than ball bearings of the same envelope. The 40 × 61.5 × 17.5 mm dimensions place this bearing in a compact, high-capacity class suitable for gearbox shaft support.
-
Nylon cage: The nylon cage provides low friction and noise damping in the oil-lubricated environment of a gearbox, and contributes to the bearing's relatively light weight.
-
Open configuration for oil-circuit lubrication: No integral seals; the bearing relies on the transmission oil for lubrication and cooling, consistent with the wet-sump strategy of a gearbox.
Application
The F-624126 is catalogued as an automotive gearbox bearing (and more broadly as a machinery, automobile, motor, and combustion turbine bearing). In gearbox service, it supports a gear shaft or auxiliary shaft under the radial loads generated by the gear train. Because the inner ring is omitted, the shaft journal serves as the inner raceway and must be hardened and ground to the correct diameter and surface finish for reliable bearing operation. Replacement requires gearbox disassembly and should follow the vehicle manufacturer's procedure for shaft journal inspection, bearing installation, and end-play adjustment.
Ordering & Logistics
| Item | Detail |
|---|---|
| Stock | 73 pcs |
| Minimum order | 1 pc |
| FOB price | US$10 – US$50 per piece |
| Payment | PayPal / Western Union / T/T (100% in advance) |
| Delivery | 3–4 workdays after payment |
| Shipping | DHL / FedEx / UPS / TNT |
| Ports | Shanghai / Guangzhou |
| Packing | Standard export packing |
| Brand | As required (authorized brands only) |
| Country of origin | China |
| Company | WUXI MUFA TECHNOLOGY CO.,LTD. |
| Sales | Alice Wong |
| [email protected] | |
| +86 13771165326 | |
| mufatec-bearings |















