Luoyang BoYing Bearing Co., Ltd.
Free Member
RE8016UUCCO/P5 Crossed Roller Bearing 80x120x16mm THK high percision Thin section bearing

RE8016UUCCO/P5 Crossed Roller Bearing 80x120x16mm THK High Percision Thin Section Bearing

Min. Order:
1 Piece
Payment term:
T/T
Delivery time:
3 Days After Payment
Technical Parameters:
Product Designations:
RE8016
Structure:
Crossed Roller
Inside Diameter:
80 mm
Outside Diameter:
120 mm
Thickness:
16 mm
Weight:
0.7 KG
Brand:
BYC
Precision Rating:
P5 P4 P2
Bearing Material:
GCr15 bearing steel
Seals Type:
UU
RE8016UUCCO/P5 Crossed Roller Bearing 80x120x16mm THK High Percision Thin Section Bearing

  RE8016 Crossed Roller Bearing 80x120x16mm THK high percision Thin section bearing

A. Bearing Parameter & Model Table

Structure:Crossed Roller

Type:Crossed Roller bearing

    Brand Name:BYC

Model NumberRE8016

Size (Metric):

- ID (Inner Diameter, Bore) = 80 mm

- OD (Outer Diameter) = 120 mm

- Width (Height,thickness) = 16 mm

Precision Rating:P5/P4/P2

Axial load rating Ca(KN):  1

Radial load rating Cr(KN): 30.1

Weight(Kg): 0.35

Material:GCr15 bearing steel

Types of Lubrication:Grease

Rotation part: Outer ring rotating (not inner ring)

  B. Product Description

RE8016 Crossed roller bearings are lightweight, compact bearings with thinnest possible inner and outer rings 

with high rigidity, because of its vertical arrangement of cylindrical rollers with a 90°V groove through the 

separate spacers in the deep groove rolling surface. This special design allows just one bearing to carry 

loads in all directions including radial, axial and moment loads. 

Depending on the application crossed roller bearings are divided into five types:

 

RE Standard Type (separable Inner Ring for Outer Ring Rotation)

RE standard type is an innovative bearing based on the design of the RB standard type bearing. 

The inner ring is separable while the outer ring is integrated into the main body. It is being used in cases 

where the high rotational accuracy of the outer ring is required.

RE4010,RE4510,REB5013,RE6013,RE7013,RE8016,RE9016,RE10016,RE10020,RE11012,RE11015,

RE11020,RE12016,RE12025,RE13015,RE13025,RE14016,RE14025,RE15013,RE15025,RE15030,RE16025,

RE17020,RE18025,RE19025,RE20025,RE20030,RE20035,RE22025,RE24025,RE25025,RE25030,RE25040,

RE30025,RE30035,RE30040,RE35020,RE35025,RE40035,RE40040,RE45025,RE50025,RE50040,RE50050,

RE60040 

 

C. Feature of Crossed Roller Bearing

1. High accuracy and load capacity. Precision ground V grooved ways and rollers. 

2. Withstands force in any direction. Alternately crossed rollers 45º angle.

3. Easy Installation and get used to small spaces. Threaded mounting holes in standard pattern.

4. Factory preloaded for minimum axial play and low coefficient of friction.

 

D. Product Application

Industrial Robotic arm,Reducer drive

•Percision Turntable,NC rotary table

•Rotation part of Machine tools

•Inspection instrument,Medical equipment

•Aero&Aviation equipment,Military radar etc

 

E. Installation & Cautions

1.Inspect the parts before installing:Clean bearing bracket,main axle or other parts to remove dirt or grease.

2.Place the bearing into the bearing bracket and main axle:To match the design clearance ,keep the bearing 

horizontal and insert the bearing into the bearing bracket or axle.If it is hard to install,use a rubber hammer to 

slightly hit every part of the bearing,so that the bearing can be attention to the hitting force is too large.Afterwards,

the matching status of bearing and basic face can be examined by checking the noise.For a interference fit,use 

heating or cooling to expand or shrink the parts for ease of installation. Be sure the bearing temperature does not

 exceed 80℃ . If the split inner or outer ring is acentric, please loosen the blots slightly and rotate the monolithic 

ring to adjust the concentricity of split ring, so that the bearing can be fit in the bracket.

3.Install the mounting disc:Place the mounting disc onto the bearing and align the screw holes, Screw all the bolts 

in the holes first and follow the orders show in below diagram when tightening bolts in diagonally opposite sequence,

Do not tighten bolts randomly.

Cautions:

1.The normal operating temperature of Crossed roller bearing is 10-80℃, If it is over this range,please contact BYC.

2.If a foreign substance enters inside the bearing structure, the rotation route of the roller may be damage, or the 

bearing may fail.Please clean the bearing by refill the lubricant grease.

3.Please do not remove or apply force to the bolt and nut of the split bearing.

 

F. Shipping And Payment

1. Industrial Neutral Packing,Package as your requirements.

2. Small size Bearings:Plastic vacuum packaging bag+Paper Box/Neutral Carton

3.Large size Bearings:Plastic film+Pergamyn paper+Roll tape+Wooden Box

4.Shipping:By air or By sea:DHL/TNT/UPS/EMS etc

5.Min.Order Quantity:  5 Piece/Pieces

6.Supply Ability:  1500 Units/Year

7.Port:SHANGHAI,HK,Guangzhou

8.Payment Terms:T/T

 

G. BYC Bearing Service

1.Your inquiry to our product & price will be replied within 24 hours

2.OEM & ODM projects are highly welcomed. We have strong R&D team here to help. 

3.Your business relationship with us will be confidential to any third party


Share this product to:     Let more people see your product
How can you buy RE8016UUCCO/P5 Crossed Roller Bearing 80x120x16mm THK High Percision Thin Section Bearing on the Internet?
High quality RE8016 ( 0.7 kg Mass, ID: 80 mm OD: 120 mm WD: 16 mm , P5 P4 P2 Accuracy Class , GCr15 bearing steel Material ), Just click the button " Contact Now " to mention your purchase Requirement , Quantity and Contact Method of your requested Bearing Item No. RE8016. then click the button " Send " The web site will make your purchasing information sent to the supplier's mailbox, who will come to contact you upon they get your information at the first time.
RE8016 Related Products »