CRBH11020UUT1/P5 Crossed Roller Bearings (110x160x20) Thin Section Type
CRBH11020
Bore Diameter:110 mm
Outside Diameter:160 mm
Width:20 mm
Weight:1.56 kg
The CRBH11020 bearing is a Crossed Roller Bearing CRBH Series with an inner diameter of 110 mm , an outer diameter of 160 mm, a width of 20 mm. It typically uses P5 P4 P2 grade precision tolerances and Rubber Seals type, together determine its load-bearing capacity, rotational accuracy, and applicable working conditions.
×
Detailed description
CRBH11020 Crossed roller bearings (110x160x20) Replace IKO bearing
(non-separable Inner or Outer Ring)
A. Product Description
BYC Crossed roller bearings are lightweight, compact bearings with thinnest possible inner and outer rings with high rigidity, because of its vertical arrangement of cylindrical rollers with a 90°V groove through the separate spacers in the deep groove rolling surface. This special design allows just one bearing to carry loads in all directions including radial, axial and moment loads.
CRBH Special Type (non-separable Inner or Outer Ring)
CRBH Special type is a bearing with integrated inner and outer ring. It is being used in cases where high rotational accuracy of both the inner and outer rings is required.
B. Bearing Parameter & Model Table
Structure:Crossed Roller
Type:Crossed Roller bearing
Brand Name:BYC
Model Number: CRBH11020
Size (Metric):
- ID (Inner Diameter, Bore) = 110 mm
- OD (Outer Diameter) = 160 mm
- Width (Height,thickness) = 20 mm
Precision Rating:P5/P4/P2
Radial load rating Cr(KN): 52.4
Weight(Kg): 1.56
Material:GCr15 bearing steel
Types of Lubrication:Grease
Rotation part: Inner ring or outer ring
Crossed roller bearings CRBH series:
CRBH5013A,CRBH6013A,CRBH7013A,CRBH8016A,CRBH9016A,CRBH10020A,CRBH11020A,
CRBH12025A,CRBH13025A,CRBH14025A,CRBH15025A,CRBH20025A,CRBH25025A
C. Feature of Crossed Roller Bearing
1. High accuracy and load capacity. Precision ground V grooved ways and rollers.
2. Withstands force in any direction. Alternately crossed rollers 45º angle.
3. Easy Installation and get used to small spaces. Threaded mounting holes in standard pattern.
4. Factory preloaded for minimum axial play and low coefficient of friction.
D. Product Application
•Industrial Robotic arm,Reducer drive
•Percision Turntable,NC rotary table
•Rotation part of Machine tools
•Inspection instrument,Medical equipment
•Aero&Aviation equipment,Military radar etc
E. Installation & Cautions
1.Inspect the parts before installing:Clean bearing bracket,main axle or other parts to remove dirt or grease.
2.Place the bearing into the bearing bracket and main axle:To match the design clearance ,keep the bearing horizontal and insert the bearing into the bearing bracket or axle.If it is hard to install,use a rubber hammer to slightly hit every part of the bearing,so that the bearing can be attention to the hitting force is too large.Afterwards,the matching status of bearing and basic face can be examined by checking the noise.For a interference fit,use heating or cooling to expand or shrink the parts for ease of installation. Be sure the bearing temperature does not exceed 80℃ . If the split inner or outer ring is acentric, please loosen the blots slightly and rotate the monolithic ring to adjust the concentricity of split ring, so that the bearing can be fit in the bracket.
3.Install the mounting disc:Place the mounting disc onto the bearing and align the screw holes, Screw all the bolts in the holes first and follow the orders show in below diagram when tightening bolts in diagonally opposite sequence,Do not tighten bolts randomly.
Cautions:
1.The normal operating temperature of Crossed roller bearing is 10-80℃, If it is over this range,please contact BYC.
2.If a foreign substance enters inside the bearing structure, the rotation route of the roller may be damage, or the bearing may fail.Please clean the bearing by refill the lubricant grease.
3.Please do not remove or apply force to the bolt and nut of the split bearing.
G. Shipping And Payment
1. Industrial Neutral Packing,Package as your requirements.
2. Small size Bearings:Plastic vacuum packaging bag+Paper Box/Neutral Carton
3.Large size Bearings:Plastic film+Pergamyn paper+Roll tape+Wooden Box
4.Shipping:By air or By sea:DHL/TNT/UPS/EMS etc
5.Min.Order Quantity: 5 Piece/Pieces
6.Supply Ability: 1500 Units/Year
7.Port:SHANGHAI,HK,Guangzhou
8.Payment Terms:T/T
H. BYC Bearing Service
1.Your inquiry to our product & price will be replied within 24 hours.
2.OEM & ODM projects are highly welcomed. We have strong R&D team here to help.
3.Your business relationship with us will be confidential to any third party.
Share this product to:
Let more people see your product
-
- CRBH20025UUT1/P5 Crossed Roller Bearings|Thin section 200*260*25mm Slewing bearing
- CRBH20025|Crossed Roller Bearings|tiny section 200*260*25mm CNC machine tool rotary table bearings& robot arm
-
- CRBH13025UUT1/P4 Crossed Roller Bearings|Thin section 130*190*25mm Slewing bearing
- CRBH13025|Crossed Roller Bearings|tiny section 130*190*25mm CNC machine tool rotary table bearings& robot arm
-
- RE4010UUCCO/P5 Crossed Roller Bearing 40x65x10mm THK high percision Robotic bearing
- A. Bearing Parameter & Model Table Structure:Crossed Roller Type:Crossed Roller bearing
-
- CRBH Crossed roller bearings Robotic using
- Brand Name:BYC Model Number: CRBH Size (Metric): - ID (Inner Diameter, Bore) = 50~250