|
|
Series
|
|
30302
|
|
Cone Part Number
|
|
X30302
|
|
Cup Part Number
|
|
Y30302
|
|
Design Units
|
|
Metric
|
|
Bearing Weight
|
|
0.2000 Kg
0.1000 lb
|
|
Cage Type
|
|
Stamped Steel
|
|
|
|
|
D - Cup Outer Diameter
|
|
1.6535 in
42.000 mm
|
|
d - Cone Bore
|
|
0.5906 in
15.000 mm
|
|
B - Cone Width
|
|
0.5118 in
13.000 mm
|
|
C - Cup Width
|
|
0.4331 in
11.000 mm
|
|
T - Bearing Width
|
|
0.5610 in
14.250 mm
|
|
Z - Number of Rollers Per Row
|
|
12
|
|
|
|
|
R - Cone Backface "To Clear" Radius1
|
|
0.040 in
1.020 mm
|
|
r - Cup Backface "To Clear" Radius2
|
|
0.040 in
1.02 mm
|
|
da - Cone Frontface Backing Diameter
|
|
0.75 in
19.05 mm
|
|
db - Cone Backface Backing Diameter
|
|
0.81 in
20.57 mm
|
|
Da - Cup Frontface Backing Diameter
|
|
1.54 in
39.12 mm
|
|
Db - Cup Backface Backing Diameter
|
|
1.44 in
36.58 mm
|
|
Ab - Cage-Cone Frontface Clearance
|
|
0.08 in
2.03 mm
|
|
Aa - Cage-Cone Backface Clearance
|
|
-0.01 in
-0.25 mm
|
|
a - Effective Center Location3
|
|
-0.18 in
-4.60 mm
|
|
1 These maximum fillet radii will be cleared by the bearing corners.
2 These maximum fillet radii will be cleared by the bearing corners.
3 Negative value indicates effective center inside cone backface.
|
|
|
|
|
C90 - Dynamic Radial Rating (90 million revolutions)1
|
|
1520 lbf
6750 N
|
|
C1 - Dynamic Radial Rating (1 million revolutions)2
|
|
5850 lbf
26000 N
|
|
C0 - Static Radial Rating
|
|
4980 lbf
22200 N
|
|
Ca90 - Dynamic Thrust Rating (90 million revolutions)3
|
|
740 lbf
3290 N
|
|
1 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
2 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
|
|
|
|
|
K - Factor1
|
|
2.05
|
|
e - ISO Factor2
|
|
0.29
|
|
Y - ISO Factor3
|
|
2.11
|
|
G1 - Heat Generation Factor (Roller-Raceway)
|
|
4.3
|
|
G2 - Heat Generation Factor (Rib-Roller End)
|
|
4.6
|
|
Cg - Geometry Factor
|
|
0.0375
|
|
1 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
2 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use. |
|
|
|
Share this product to: 
Let more people see your product
